View AD7895_9050771.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev. 0 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of analog devices. a AD7895 one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 617/329-4700 world wide web site: http://www.analog.com fax: 617/326-8703 ? analog devices, inc., 1996 5 v, 12-bit, serial 3.8 m s adc in 8-pin package functional block diagram signal scaling* 12-bit adc output register track/hold AD7895 v in convst v dd gnd busy sclk sdata ref in *AD7895-10, AD7895-3 features fast 12-bit adc with 3.8 m s conversion time 8-pin mini-dlp and soic single 5 v supply operation high speed, easy-to-use, serial interface on-chip track/hold amplifier selection of input ranges 6 10 v for AD7895-10 6 2.5 v for AD7895-3 0 v to +2.5 v for AD7895-2 high input impedance low power: 20 mw max 14-bit pin compatible upgrade (ad7894) general description the AD7895 is a fast 12-bit adc that operates from a single +5 v supply and is housed in a small 8-pin mini-dip and 8-pin soic. the part contains a 3.8 m s successive approximation a/d converter, an on-chip track/hold amplifier, an on-chip clock and a high speed serial interface. output data from the AD7895 is provided via a high speed, serial interface port. this two-wire serial interface has a serial clock input and a serial data output with the external serial clock accessing the serial data from the part. in addition to the traditional dc accuracy specifications such as linearity and full-scale and offset errors, the AD7895 is specified for dynamic performance parameters, including harmonic distortion and signal-to-noise ratio. the part accepts an analog input range of 10 v (AD7895-10), 2.5 v (AD7895-3), 0 v to 2.5 v (AD7895-2) and operates from a single +5 v supply, consuming only 20 mw max. the AD7895 features a high sampling rate mode and, for low power applications, a proprietary automatic power-down mode where the part automatically goes into power down once conversion is complete and wakes up before the next conver- sion cycle. the part is available in a small, 8-pin, 0.3" wide, plastic dual-in- line pac kage (mini-dip) and in an 8-pin, small outline ic (soic). product highlights 1. fast, 12-bit adc in 8-pin package the AD7895 contains a 3.8 m s adc, a track/hold amplifier, control logic and a high speed serial interface, all in an 8-pin package. this offers considerable space saving over alterna- tive solutions. 2. low power, single supply operation the AD7895 operates from a single +5 v supply and consumes only 20 mw. the automatic power-down mode, where the part goes into power-down once conversion is complete and wakes up before the next conversion cycle, makes the AD7895 ideal for battery-powered or portable applications. 3. high speed serial interface the part provides high speed serial data and serial clock lines allowing for an easy, two-wire serial interface arrangement.
AD7895* product page quick links last content update: 02/23/2017 comparable parts view a parametric search of comparable parts. documentation data sheet ? AD7895: 5 v, 12-bit, serial 3.8 s adc in 8-pin package data sheet product highlight ? 8- to 18-bit sar adcs ... from the leader in high performance analog reference materials technical articles ? ms-2210: designing power supplies for high speed adc design resources ? AD7895 material declaration ? pcn-pdn information ? quality and reliability ? symbols and footprints discussions view all AD7895 engineerzone discussions. sample and buy visit the product page to see pricing options. technical support submit a technical question or find your regional support number. document feedback submit feedback for this data sheet. this page is dynamically generated by analog devices, inc., and inserted into this data sheet. a dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. this dynamic page may be frequently modified.
C2C rev. 0 AD7895Cspecifications parameter a versions l b versions units test conditions/comments dynamic performance 2 signal to (noise + distortion) ratio 3 @ +25 c 70 70 db min f in = 50 khz sine wave, f sample = 200 khz t min to t max 70 70 db min total harmonic distortion (thd) 3 C78 C78 db max f in = 50 khz sine wave, f sample = 200 khz, typically C87 db peak harmonic or spurious noise 3 C89 C89 db typ f in = 50 khz sine wave, f sample = 200 khz intermodulation distortion (imd) 3 fa = 9 khz, fb = 9.5 khz, f sample = 200 khz 2nd order terms C87 C87 db typ 3rd order terms C87 C87 db typ dc accuracy resolution 12 12 bits minimum resolution for which no missing codes are guaranteed 12 12 bits relative accuracy 3 1 1 lsb max typically 0.4 lsb differential nonlinearity 3 1 1 lsb max positive full-scale error 3 3 2 lsb max AD7895-2 unipolar offset error 3 2 lsb max AD7895-10, AD7895-3 only negative full-scale error 3 3 2 lsb max bipolar zero error 4 3 lsb max analog input AD7895-10 input voltage range 10 10 volts input resistance 24 24 k w min AD7895-3 input voltage range 2.5 2.5 volts input resistance 9 9 k w min AD7895-2 input voltage range 0 to +2.5 0 to +2.5 volts input current 500 500 na max reference input ref in input voltage range 2.375/2.625 2.375/2.625 v min/v max 2.5 v 5% input current 1 1 m a max input capacitance 3 10 10 pf max logic inputs input high voltage, v inh 2.4 2.4 v min v dd = 5 v 5% input low voltage, v inl 0.8 0.8 v max v dd = 5 v 5% input current, i in 10 10 m a max v in = 0 v to v dd input capacitance, c in 4 10 10 pf ax logic outputs output high voltage, v oh 4.0 4.0 v min i source = 200 m a output low voltage, v ol 0.4 0.4 v max i sink = 1.6 ma output coding AD7895-10, AD7895-3 2s complement AD7895-2 straight (natural) binary conversion rate conversion time mode 1 operation 3.8 3.8 m s max mode 2 operation 5 9.8 9.8 m s max track/hold acquisition time 3 0.5 0.5 m s max power requirements v dd +5 +5 v nom 5% for specified performance i dd 4 4 ma max digital inputs @ v dd , v dd = 5 v 5% power dissipation 20 20 mw max typically 16 mw power-down mode i dd @ +25 c55 m a max digital inputs @ gnd, v dd = 5 v 5% t min to t max 10 10 m a max digital inputs @ gnd, v dd = 5 v 5% power dissipation @ +25 c2525 m w max notes 1 temperature ranges are as follows: a, b versions: C40 c to +85 c. 2 applies to mode 1 operation. see section on operating modes. 3 see terminology. 4 sample tested @ +25 c to ensure compliance. 5 this 9.8 m s includes the wake-up time from standby. this wake-up time is timed from the rising edge of convst , whereas conversion is timed from the falling edge of convst , for narrow convst pulse width the conversion time is effectively the wake-up time plus conversion time hence 9.8 m s. this can be seen from figure 3. note that if the convst pulse width is greater than 6 m s then the effective conversion time will increase beyond 9.8 m s. specifications subject to change without notice. (v dd = +5 v, gnd = 0 v, ref in = +2.5 v. all specifications t min to t max unless otherwise noted)
AD7895 C3C rev. 0 timing characteristics 1, 2 parameter a, b versions units test conditions/comments t 1 40 ns min convst pulse width t 2 35 2 ns min sclk high pulse width t 3 35 2 ns min sclk low pulse width t 4 60 3 ns max data access time after falling edge of sclk, v dd = 5 v 5% t 5 10 ns min data hold time after falling edge of sclk t 6 50 4 ns max bus relinquish time after falling edge of sclk notes 1 sample tested at +25 c to ensure compliance. all input signals are measured with tr = tf = 1 ns (10% to 90% of +5 v) and timed from a voltage level of +1.4 v. 2 the sclk maximum frequency is 15 mhz. care must be taken when interfacing to account for the data access time, t 4 , and the setup time required for the user's processor. these two times will determine the maximum sclk frequency that the users system can operate with. see serial interface section for more information. 3 measured with the load circuit of figure 1 and defined as the time required for an output to cross 0.8 v or 2.0 v. 4 derived from the measured time taken by the data outputs to change 0.5 v when loaded with the circuit of figure 1. the measured number is then extrapolated back to remove the effects of charging or discharging the 50 pf capacitor. this means that the time, t 6 , quoted in the timing characteristics is the true bus relinquish time of the part and, as such, is independent of external bus loading capacitances. absolute maximum ratings* (t a = +25 c unless otherwise noted) v dd to gnd . . . . . . . . . . . . . . . . . . . . . . . . . . C0.3 v to +7 v analog input voltage to gnd AD7895-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 v AD7895-2, AD7895-3 . . . . . . . . . . . . . . . . . . . C5 v, +10 v reference input voltage to gnd . . . . C0.3 v to v dd + 0.3 v digital input voltage to gnd . . . . . . . C0.3 v to v dd + 0.3 v digital output voltage to gnd . . . . . C0.3 v to v dd + 0.3 v operating temperature range commercial (a, b versions) . . . . . . . . . . . C40 c to +85 c storage temperature range . . . . . . . . . . . C65 c to +150 c junction temperature . . . . . . . . . . . . . . . . . . . . . . . . +150 c plastic dip package, power dissipation . . . . . . . . . . 450 mw q ja thermal impedance . . . . . . . . . . . . . . . . . . . . 130 c/w lead temperature (soldering, 10 sec) . . . . . . . . . . +260 c soic package, power dissipation . . . . . . . . . . . . . . . 450 mw q ja thermal impedance . . . . . . . . . . . . . . . . . . . . 170 c/w lead temperature, soldering vapor phase (60 sec) . . . . . . . . . . . . . . . . . . . . . +215 c infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220 c warning! esd sensitive device caution esd (electrostatic discharge) sensitive device. electrostatic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge without detection. although the AD7895 features proprietary esd protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality. (v dd = +5 v, gnd = 0 v, ref in = +2.5 v) *stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. ordering guide model temperature range linearity error (lsb) snr (db) package option* AD7895an-2 C40 c to +85 c 1 lsb 70 db n-8 AD7895ar-2 C40 c to +85 c 1 lsb 70 db so-8 AD7895br-2 C40 c to +85 c 1 lsb 70 db so-8 AD7895an-10 C40 c to +85 c 1 lsb 70 db n-8 AD7895ar-10 C40 c to +85 c 1 lsb 70 db so-8 AD7895br-10 C40 c to +85 c 1 lsb 70 db so-8 AD7895an-3 C40 c to +125 c 1 lsb 70 db n-8 AD7895ar-3 C40 c to +85 c 1 lsb 70 db so-8 *n = plastic dip, so = soic. +1.6v 2.0ma 2.0ma 50pf to output pin figure 1. load circuit for access time and bus relinquish time
AD7895 C4C rev. 0 pin function description pin pin no. mnemonic description 1 ref in voltage reference input. an external reference source should be connected to this pin to provide the refer- ence voltage for the AD7895s conversion process. the ref in input is buffered on chip. the nominal ref- erence voltage for correct operation of the AD7895 is +2.5 v. 2v in analog input channel. the analog input range is 10 v (AD7895-10), 2.5 v (AD7895-3) and 0 v to +2.5 v (AD7895-2). 3 gnd analog ground. ground reference for track/hold, comparator, digital circuitry and dac. 4 sclk serial clock input. an external serial clock is applied to this input to obtain serial data from the AD7895. a new serial data bit is clocked out on the falling edge of this serial clock. data is guaranteed valid for 10 ns after this falling edge so that data can be accepted on the falling edge when a fast serial clock is used. the serial clock input should be taken low at the end of the serial data transmission. 5 sdata serial data output. serial data from the AD7895 is provided at this output. the serial data is clocked out by the falling edge of sclk, but the data can also be read on the falling edge of sclk. this is possible because data bit n is valid for a specified time after the falling edge of sclk ( data hold time) (see figure 4). sixteen bits of serial data are provided with four leading zeros followed by the 12 bits of conversion data. on the sixteenth falling edge of sclk, the sdata line is held for the data hold time and then is disabled (three-stated). output data coding is 2s complement for the AD7895-10, AD7895-3 and straight binary for the AD7895-2. 6 busy the busy pin is used to indicate when the part is doing a conversion. the busy pin will go high on the falling edge of convst and will return low when the conversion is complete. 7 convst convert start. edge-triggered logic input. on the falling edge of this input, the track/hold goes into its hold mode, and conversion is initiated. if convst is low at the end of conversion, the part goes into power- down mode. in this case, the rising edge of convst wakes up the part. 8v dd positive supply voltage, +5 v 5%. pin configuration dip and soic 1 2 3 4 8 7 6 5 top view (not to scale) AD7895 ref in sdata busy convst v dd v in gnd sclk
AD7895 C5C rev. 0 terminology signal to (noise + distortion) ratio this is the measured ratio of signal to (noise + distortion) at the output of the a/d converter. the signal is the rms amplitude of the fundamental. noise is the rms sum of all nonfundamental signals up to half the sampling frequency (f s /2), excluding dc. the ratio is dependent upon the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. the theoretical signal to (noise + distortion) ratio for an ideal n-bit converter with a sine wave input is given by: signal to ( noise + distortion ) = (6.02 n + 1.76) db thus for a 12-bit converter, this is 74 db. total harmonic distortion total harmonic distortion (thd) is the ratio of the rms sum of harmonics to the fundamental. for the AD7895, it is defined as: thd ( db ) = 20 log v 2 2 + v 3 2 + v 4 2 + v 5 2 + v 6 2 v 1 where v 1 is the rms amplitude of the fundamental, and v 2 , v 3 , v 4 , v 5 and v 6 are the rms amplitudes of the second through the sixth harmonics. peak harmonic or spurious noise peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the adc output spectrum (up to f s /2 and excluding dc) to the rms value of the fundamental. normally, the value of this specification is determined by the largest harmonic in the spectrum, but for parts where the harmonics are buried in the noise floor, it will be a noise peak. intermodulation distortion with inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities will create distortion products at sum and difference frequencies of mfa nfb where m, n = 0, 1, 2, 3, etc. intermodulation terms are those for which neither m or n are equal to zero. for example, the second order terms include (fa + fb) and (fa C fb), while the third order terms include (2 fa + fb), (2 fa C fb), (fa + 2 fb) and (fa C 2 fb). the AD7895 is tested using the ccif standard where two input frequencies near the top end of the input bandwidth are used. in this case, the second and third order terms are of different significance. the second order terms are usually distanced in frequency from the original sine waves, while the third order terms are usually at a frequency close to the input frequencies. as a result, the second and third order terms are specified separately. the calculation of the intermodulation distortion is as per the thd specification where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the fundamental expressed in dbs. relative accuracy relative accuracy or endpoint nonlinearity is the maximum deviation from a straight line passing through the endpoints of the adc transfer function. differential nonlinearity this is the difference between the measured and the ideal 1 lsb change between any two adjacent codes in the adc. positive full-scale error (AD7895-10) this is the deviation of the last code transition (01 . . . 110 to 01 . . . 111) from the ideal (4 vref C 1 lsb) after the bipolar zero error has been adjusted out. positive full-scale error (AD7895-3) this is the deviation of the last code transition (01 . . . 110 to 01 . . . 111) from the ideal ( vref C 1 lsb) after the bipolar zero error has been adjusted out. positive full-scale error (AD7895-2) this is the deviation of the last code transition (11 . . . 110 to 11 . . . 111) from the ideal (vref C 1 lsb) after the unipolar offset error has been adjusted out. bipolar zero error (AD7895-10, AD7895-3) this is the deviation of the midscale transition (all 0s to all 1s) from the ideal 0 v (gnd). unipolar offset error (AD7895-2) this is the deviation of the first code transition (00 . . . 000 to 00 . . . 001) from the ideal 1 lsb. negative full-scale error (AD7895-10) this is the deviation of the first code transition (10 . . . 000 to 10 . . . 001) from the ideal (C4 vref + 1 lsb) after bipolar zero error has been adjusted out. negative full-scale error (AD7895-3) this is the deviation of the first code transition (10 . . . 000 to 10 . . . 001) from the ideal (Cvref + 1 lsb) after bipolar zero error has been adjusted out. track/hold acquisition time track/hold acquisition time is the time required for the output of the track/hold amplifier to reach its final value, within 1/2 lsb, after the end of conversion (the point at which the track/hold returns to track mode). it also applies to situations where there is a step input change on the input voltage applied to the v in input of the AD7895. this means that the user must wait for the duration of the track/hold acquisition time after the end of conversion or after a step input change to v in before starting another conversion to ensure that the part operates to specification.
AD7895 C6C rev. 0 converter details the AD7895 is a fast, 12-bit single supply a/d converter. it provides the user with signal scaling, track/hold, a/d converter and serial interface logic functions on a single chip. the a/d converter section of the AD7895 consists of a conventional successive-approximation converter based around an r-2r ladder structure. the signal scaling on the AD7895-10 and AD7895-3 allows the part to handle 10 v and 2.5 v input signals, respectively, while operating from a single +5 v supply. the AD7895-2 accepts an analog input range of 0 v to +2.5 v. the part requires an external +2.5 v reference. the reference input to the part is buffered on-chip. the AD7895 has two operating modes, the high sampling mode and the auto sleep mode, where the part automatically goes into sleep after the end of conversion. these modes are discussed in more detail in the timing and control section. a major advantage of the AD7895 is that it provides all of the above functions in an 8-pin package, either 8-pin mini-dip or soic. this offers the user considerable spacing saving advantages over alternative solutions. the AD7895 consumes only 20 mw maximum, making it ideal for battery-powered applications. conversion is initiated on the AD7895 by pulsing the convst input. on the falling edge of convst , the on-chip track/hold goes from track to hold mode, and the conversion sequence is started. the conversion clock for the part is generated internally using a laser-trimmed clock oscillator circuit. conversion time for the AD7895 is 3.8 m s in the high sampling mode (9.8 m s for the auto sleep mode), and the track/hold acquisition time is 0.3 m s. to obtain optimum performance from the part, the read operation should not occur during the conversion or during 300 ns prior to the next conversion. this allows the part to operate at throughput rates up to 192 khz and achieve data sheet specifications. circuit description analog input section the AD7895 is offered as three part types: the AD7895-10, which handles a 10 v input voltage range; the AD7895-3, which handles input voltage range 2.5 v; and the AD7895-2, which handles a 0 v to +2.5 v input voltage range. agnd AD7895-10/AD7895-3 v in ref in track/ hold to adc reference circuitry to internal comparator r3 r2 r1 figure 2. AD7895-10/AD7895-3 analog input structure figure 2 shows the analog input section for the AD7895-10 and AD7895-3. the analog input range of the AD7895-10 is 10 v into an input resistance of typically 33 k w . the analog input range of the AD7895-3 is 2.5 v into an input resistance of typically 12 k w. this input is benign with no dynamic charging curre nts, as the resistor stage is followed by a high input imped- ance stage of the track/hold amplifier. for the AD7895-10, r1 = 30 k w , r2 = 7.5 k w and r3 = 10 k w . for the AD7895-3, r1 = r2 = 6.5 k w and r3 is open circuit. for the AD7895-10 and AD7895-3, the designed code transi- tions occur on succe ssive integer lsb values (i.e., 1 lsb, 2 lsbs, 3 lsbs . . .). output coding is 2s complement binary with 1 lsb = fs/4096. the ideal input/output transfer function for the AD7895-10 and AD7895-3 is shown in table i. table i. ideal input/output code table for the AD7895-10/-3 digital output analog input l code transition +fsr/2 C 1 lsb 2 011 . . . 110 to 011 . . . 111 +fsr/2 C 2 lsbs 011 . . . 101 to 011 . . . 110 +fsr/2 C 3 lsbs 011 . . . 100 to 011 . . . 101 gnd + 1 lsb 000 . . . 000 to 000 . . . 001 gnd 111 . . . 111 to 000 . . . 000 gnd C 1 lsb 111 . . . 110 to 111 . . . 111 Cfsr/2 + 3 lsbs 100 . . . 010 to 100 . . . 011 Cfsr/2 + 2 lsbs 100 . . . 001 to 100 . . . 010 Cfsr/2 + 1 lsb 100 . . . 000 to 100 . . . 001 notes 1 fsr is full-scale range = 20 v (AD7895-10) and = 5 v (AD7895-3) with ref in = +2.5 v. 2 1 lsb = fsr/4096 = 4.883 mv (AD7895-10) and 1.22 mv (AD7895-3) with ref in = +2.5 v. the analog input section for the AD7895-2 contains no biasing resistors, and the v in pin drives the input to the track/hold amplifier directly. the analog input range is 0 v to +2.5 v into a high impedance stage with an input current of less than 500 na. this input is benign with no dynamic charging cur- rents. once again, the designed code transitions occur on succes- sive integer lsb values. output coding is straight (natural) binary with 1 lsb = fs/4096 = 2.5 v/4096 = 0.61 mv. table ii shows the ideal input/output transfer function for the AD7895-2. table ii. ideal input/output code table for AD7895-2 digital output analog input 1 code transition +fsr C 1 lsb 2 111 . . . 110 to 111 . . . 111 +fsr C 2 lsb 111 . . . 101 to 111 . . . 110 +fsr C 3 lsb 111 . . . 100 to 111 . . . 101 gnd + 3 lsb 000 . . . 010 to 000 . . . 011 gnd + 2 lsb 000 . . . 001 to 000 . . . 010 gnd + 1 lsb 000 . . . 000 to 000 . . . 001 notes 1 fsr is full-scale range and is 2.5 v for AD7895-2 with vref = +2.5 v. 2 1 lsb = fsr/4096 and is 0.61 mv for AD7895-2 with vref = +2.5 v. track/hold section the track/hold amplifier on the analog input of the AD7895 allows the adc to accurately convert an input sine wave of full- scale amplitude to 12-bit accuracy. the input bandwidth of the track/hold is greater than the nyquist rate of the adc even when the adc is operated at its maximum throughput rate of 192 khz (i.e., the track/hold can handle input frequencies in excess of 100 khz).
AD7895 C7C rev. 0 the track/hold amplifier acquires an input signal to 12-bit accuracy in less than 0.3 m s. the operation of the track/hold is essentially transparent to the user. with the high sampling operating mode, the track/hold amplifier goes from its tracking mode to its hold mode at the start of conversion (i.e. the falling edge of convst ). the aperture time for the track/hold (i.e. the delay time between the external convst signal and the track/hold actually going into hold) is typically 15 ns. at the end of conversion (on the falling edge of busy), the part ret urns to its tracking mode. the acquisition time of the track/hold amplifier begins at this point. for the auto shut down mode, the rising edge of convst wakes up the part and the track, and hold amplifier goes from its tracking mode to its hold mode 6 m s after the rising edge of convst (provided that the convst high time is less than 6 m s). once again, the part returns to its tracking mode at the end of conversion when the busy signal goes low. reference input the reference input to the AD7895 is buffered on-chip with a maximum reference input current of 1 m a. the part is specified with a +2.5 v reference input voltage. errors in the reference source will result in gain errors in the AD7895s transfer function and will add to the specified full-scale errors on the part. suitable reference sources for the AD7895 include the ad780 and ad680 precision +2.5 v references. timing and control section figure 3 shows the timing and control sequence required to obtain optimum performance from the AD7895. in the se- quence shown, conversion is initiated on the falling edge of convst , and new data from this conversion is available in the output register of the AD7895 3.8 m s later. once the read operation has taken place, a further 300 ns should be allowed before the next falling edge of convst to optimize the settling of the track/hold amplifier before the next conversion is initi- ated. with the serial clock frequency at its maximum of 15 mhz, the achievable throughput rate for the part is 3.8 m s (conversion time) plus 1.1 m s (read time) plus 0.3 m s (acquisi- tion time). this results in a minimum throughput time of 8.2 m s (equivalent to a throughput rate of 192 khz). a serial clock of less than 15 mhz can be used, but this will in turn mean that the throughput time will increase. the read operation consists of sixteen serial clock pulses to the output shift register of the AD7895. after sixteen serial clock pulses, the shift register is reset, and the sdata line is three- stated. if there are more serial clock pulses after the sixteenth clock, the shift register will be moved on past its reset state. however, the shift register will be reset again on the falling edge of the convst signal to ensure that the part returns to a known state every conversion cycle. as a result, a read opera- tion from the output register should not straddle across the falling edge of convst as the output shift register will be reset in the middle of the read operation, and the data read back into the microprocessor will appear invalid. operating modes mode 1 operation (high sampling performance) the timing diagram in figure 3 is for optimum performance in operating mode 1 where the falling edge of convst starts conversion and puts the track/hold amplifier into its hold mode. this falling edge of convst also causes the busy signal to go high to indicate that a conversion is taking place. the busy signal goes low when the conversion is complete, which is 3.8 m s max after the falling edge of convst , and new data from this conversion is available in the output register of the AD7895. a read operation accesses this data. this read operation consists of 16 clock cycles, and the length of this read operation will depend on the serial clock frequency. for the fastest throughput rate (with a serial clock of 15 mhz, 5 v operation) the read operation will take 1.1 m s. the read opera- tion must be complete at least 300 ns before the falling edge of the next convst , and this gives a total time of 5.2 m s for the full throughput time (equivalent to 192 khz). this mode of operation should be used for high sampling applications. mode 2 operation (auto sleep after conversion) the timing diagram in figure 4 is for optimum performance in operating mode 2 where the part automatically goes into sleep mode once busy goes low after conversion and wakes-up before the next conversion takes place. this is achieved by keep- ing convst low at the end of conversion, whereas it was high at the end of conversion for mode 1 operation. the rising edge of convst wakes up the part. this wake-up time is 6 m s at which point the track/hold amplifier goes into its hold mode, provided the convst has gone low. the conversion takes 3.8 m s after this giving a total of 9.8 m s from the rising edge of convst to the conversion being complete, which is indi- cated by the busy going low. note that since the wake-up time from the rising edge of convst is 6 m s, when the convst pulse width is greater than 6 m s, the conversion will take more convst busy sclk serial read operation conversion ends 3.8? later output serial shift register is reset conversion is initiated and track/hold goes into hold t 1 = 40ns min 300ns min t 1 t convert = 3.8? read operation should end 300ns prior to next falling edge of convst figure 3. mode 1 timing operation diagram for high sampling performance
AD7895 C8C rev. 0 than the 9.8 m s shown in diagram from the rising edge of convst . this is because the track/hold amplifier goes into its hold mode on the falling edge of convst , and the conver- sion will not be complete for a further 3.8 m s. in this case, the busy will be the best indicator for when the conversion is complete. even though the part is in sleep mode, data can still be read from the part. the read operation consists of 16 clock cycles as in mode 1 operation. for the fastest serial clock of 15 mhz, the read operation will take 1.1 m s and this must be complete at least 300 ns before the falling edge of the next convst to allow the track/hold amplifier to have enough time to settle. this mode is very useful when the part is convert- ing at a slow rate as the power consumption will be significantly reduced from that of mode 1 operation. serial interface the serial interface to the AD7895 consists of just three wires: a serial clock input (sclk), the serial data output (sdata) and a conversion status output (busy). this allows for an easy-to- use interface to most microcontrollers, dsp processors and shift registers. figure 5 shows the timing diagram for the read operation to the AD7895. the serial clock input (sclk) provides the clock source for the serial interface. serial data is clocked out from the sdata line on the falling edge of this clock and is valid on both the rising and falling edges of sclk. the advantage of having the data valid on both the rising and falling edges of the sclk is that it gives the user greater flexibility in interfacing to the part and allows a wider range of microprocessor and micro- controller interfaces to be accommodated. this also explains the two timing figures, t 4 and t 5, that are quoted on the diagram. the time t 4 specifies how long after the falling edge of the sclk that the next data bit becomes valid, whereas the time t 5 specifies how long after the falling edge of the sclk that the current data bit is valid for. the first leading zero is clocked out on the first rising edge of sclk. note that the first zero will be valid on the first falling edge of sclk even though the data access time is specified at 60 ns for the other bits. the reason that the first bit will be clocked out faster than the other bits is due to the internal architecture of the part. sixteen clock pulses must be provided to the part to access to full conversion result. the AD7895 provides four leading zeros, followed by the 12-bit conversion result starting with the msb (db11). the last data bit to be clocked out on the penultimate falling clock edge is the lsb (db0). on the sixteenth falling edge of sclk, the lsb (db0) will be valid for a specified time to allow the bit to be read on the falling edge of the sclk, then the sdata line is disabled (three-stated). after this last bit has been clocked out, the sclk input should return low and remain low until the next serial data read operation. if there are extra clock pulses after the sixteenth clock, the AD7895 will start over again with outputting d ata from its output register, and the data bus will no longer be three-stated even when the clock stops. provided the serial clock has stopped before the next falling edge of convst , the AD7895 will continue to operate correctly w ith the output shift register being reset on the falling e dge of convst. however, the sclk line must be low when convst goes low in order to reset the output shift register correctly. the serial clock input does not have to be continuous during the serial read operation. the sixteen bits of data (four leading zeros and 12 bit conversion result) can be read from the AD7895 in a number of bytes. the AD7895 counts the serial clock edges to know which bit from the output register should be placed on the sdata output. to ensure that the part does not lose synchronization, the serial clock counter is reset on the falling edge of the convst input, provided the sclk line is low. the user should ensure that the sclk line remains low until the end of the conversion. when the conversion is complete, busy goes low, the output register will be loaded with the new conversion result and can be read from with sixteen clock cycles of sclk. convst busy sclk serial read operation conversion ends 9.8? later read operation should end 300ns prior to next falling edge of convst output serial shift register is reset part wakes up conversion is initiated track/hold goes into hold t 1 = 6? wake-up time t 1 t convert = 9.8? 300ns min figure 4. mode 2 timing diagram where automatic sleep function is initiated t 2 4 leading zeros dout (o/p) sclk ( i/p) t 6 1 2 3 4 5 6 15 16 db0 db10 db11 3-state t 5 t 3 t 4 3-state t 2 = t 3 = 35ns min, t 4 = 60ns max, t 5 = 10ns min, t 6 = 50ns max @ 5v, a, b, versions figure 5. data read operation
AD7895 C9C rev. 0 microprocessor/microcontroller interface the AD7895 provides a three-wire serial interface that can be used for connection to the serial ports of dsp processors and microcontr ollers. figures 6 through 9 show the AD7895 interfaced to a number of different microcontrollers and dsp processors. the AD7895 accepts an external se rial clock, and as a result, in all interfaces shown here, the processor/ controller is configured as the master, providing the serial clock with the AD7895 configured as the slave in the system. AD7895C8051 interface figure 6 shows an interface between the AD7895 and the 8xl51 microcontroller. the 8xl51 is configured for its mode 0 serial interface mode. the diagram shows the simplest form of the interface where the AD7895 is the only part connected to the serial port of the 8xl51 and, therefore, no decoding of the serial read operations is required. AD7895 sdata sclk busy p3.0 p3.1 8x51/l51 p1.2 or int1 figure 6. AD7895 to 8x51/l51 interface to chip select the AD7895 in systems where more than one device is connected to the 8xl51s serial port, a port bit configured as an output, from one of the 8xl51s parallel ports can be used to gate on or off the serial clock to the AD7895. a simple and function on this port bit and the serial clock from the 8xl51 will provide this function. the port bit should be high to select the AD7895 and low when it is not selected. the end of conversion is monitored by using the busy signal that is shown in the interface diagram of figure 6. the busy line from the AD7895 is connected to the port p1.2 of the 8xl51 so the busy line can be polled by the 8xl51. the busy line can be connected to the int1 line of the 8xl51 if an interrupt driven system is preferred. these two options are shown in the diagram. note also that the AD7895 outputs the msb first during a read operation, while the 8xl51 expects the lsb first. therefore, the data which is read into the serial buffer needs to be rear- ranged before the correct data format from the AD7895 appears in the accumulator. the serial clock rate from the 8xl51 is limited to significantly less than the allowable input serial clock frequency with which the AD7895 can operate. as a result, the time to read data from the part will actually be longer than the conversion time of the part. this means that the AD7895 cannot run at its maximum throughput rate when used with the 8xl51. AD7895C68hc11/l11 interface an interface circuit between the AD7895 and the 68hc11/l11 microcontroller is shown in figure 7. for the interface shown, the 68l11 spi port is used, and the 68l11 is configured in its single-chip mode. the 68l11 is configured in the master mode with its cpol bit set to a logic zero and its cpha bit set to a logic one. as with the previous interface, the diagram shows the simplest form of the interface where the AD7895 is the only part connected to the serial port of the 68l11 and, therefore, no decoding of the serial read operations is required. AD7895 sdata sclk busy sck miso 68hc11/l11 pc2 or irq figure 7. AD7895 to 68hc11/l11 interface once again, to chip select the AD7895 in systems where more than one device is connected to the 68hc11s serial port, a port bit configured as an output from one of the 68hc11s parallel ports can be used to gate on or off the serial clock to the AD7895. a simple and function on this port bit and the serial clock from the 68l11 will provide this function. the port bit should be high to select the AD7895 and low when it is not selected. the end of conversion is monitored by using the busy signal that is shown in the interface diagram of figure 7. with the busy line from the AD7895 connected to the port pc0 of the 68hc1 1/l11, the busy line can be polled by the 68hc11/ l11. the busy line can be connected to the irq line of the 68hc11/l11 if an interrupt driven system is preferred. these two options are shown in the diagram. the serial clock rate from the 68hc11/l11 is limited to significantly less than the allowable input serial clock frequency with which the AD7895 can operate. as a result, the time to read data from the part will actually be longer than the conver- sion time of the part. this means that the AD7895 cannot run at its maximum throughput rate when used with the 68hc11/l11. AD7895Cadsp-2103/5 interface an interface circuit between the AD7895 and the adsp-2103/5 dsp processor is shown in figure 8. in the interface shown, the rfs1 output from the adsp-2103/5s sport1 serial port is used to gate the serial clock (sclk1) of the adsp-2103/5 before it is applied to the sclk input of the AD7895. the rfs1 output is configured for active high operation. the busy line from the AD7895 is connected to the irq2 line of the adsp-2103/5 so that at the end of conversion an interrupt is generated telling the adsp-2103/5 to initiate a read operation. the interface ensures a noncontinuous clock for the AD7895s serial clock input with only sixteen serial clock pulses provided and the serial clock line of the AD7895 remaining low between data transfers. the sdata line from the AD7895 is connected to the dr1 line of the adsp-2103/5s serial port.
AD7895 C10C rev. 0 AD7895 sdata sclk busy sclk1 dr1 adsp-2103/5 irq2 rfs1 figure 8. ad7896 to adsp-2103 /5 interface the timing relationship between the sclk1 and rfs1 outputs of the adsp-2103/5 are such that the delay between the rising edge of the sclk1 and the rising edge of an active high rfs1 is up to 30 ns. there is also a requirement that data must be set up 10 ns prior to the falling edge of the sclk1 to be read correctly by the adsp-2103/5. the data access time for the AD7895 is 60 ns (5 v (a, b versions)) from the rising edge of its sclk input. assuming a 10 ns propagation delay through the external and gate, the high time of the sclk1 output of the adsp-2105 must be 3 (30 + 60 +10 +10) ns, i.e., 3 110 ns. this means that the serial clock frequency with which the interface of figure 8 can work is limited to 4.5 mhz. however, there is an alternative method that allows for the adsp-2105 sclk1 to run at 5 mhz ( the max serial clock f requency of the sclk1 output). the arrangement occurs when the first leading zero of the data stream from the AD7895 cannot be guaranteed to be clocked into the adsp-2105 due to the combined delay of the rfs signal and the data access time of the AD7895. in most cases, this is acceptable because there will still be three leading zeros followed by the 12 data bits. for the adsp-2103, the sclk1 frequency will need to be limited to < 4 mhz to account for the 100 ns data access time of the AD7895. another alternative scheme is to configure the adsp-2103/5 so that it accepts an external noncontinuous serial clock. in this case, an external noncontinuous serial clock is provided that drives the serial clock inputs of both the adsp-2103/5 and the AD7895. in this scheme, the serial clock frequency is limited to 15 mhz by the AD7895. AD7895Cdsp56002/l002 interface figure 9 shows an interface circuit between the AD7895 and the dsp56002/l002 dsp processor. the dsp56002/l002 is configured for normal mode asynchronous operation with gated clock. it is also set up for a 16-bit word with sck as gated clock output. in this mode, the dsp56002/l002 provides sixteen serial clock pulses to the AD7895 in a serial read operation. because the dsp56002/l002 assumes valid data on the first falling edge of sck, the interface is simply two-wire as shown in figure 9. AD7895 sdata sclk busy sck sdr dsp56002/l002 moda / irqa figure 9. AD7895 to dsp56002/l002 interface because the busy line from the AD7895 is connected to the moda/ irqa input of the dsp56002/l002, an interrupt will be generated at the end of conversion. this ensures that the read operation will take place after conversion is finished. AD7895 performance linearity the linearity of the AD7895 is determined by the on-chip 12-bit d/a converter. this is a segmented dac that is laser trimmed for 12-bit integral linearity and differential linearity. typical relative accuracy numbers for the part are 1/4 lsb while the typical dnl errors are 1/2 lsb. noise in an a/d converter, noise exhibits itself as code uncertainty in dc applications and as the noise floor (in an fft, for example) in ac applications. in a sampling a/d converter like the AD7895, all information about the analog input appears in the baseband from dc to 1/2 the sampling frequency. the input bandwidth of the track/hold exceeds the nyquist bandwidth and, therefore, an antialiasing filter should be used to remove unwanted signals above f s /2 in the input signal in applications where such signals ex ist. figure 10 shows a histogram plot for 8192 conversions of a dc input using the AD7895. the analog input was set at the center of a code transition. it can be seen that almost all the codes appear in the one output bin, indicating very good noise performance from the adc. 957 962 958 959 960 961 0 4000 3000 2000 1000 6000 5000 7000 8000 9000 figure 10. histogram of 8192 conversions of a dc input in this case where the output data read for the device occurs during conversion, this has the effect of injecting noise onto the die while bit decisions are being made, and this increases the noise generated by the AD7895. a histogram plot for 8192 conversions of the same dc input would show a larger spread of codes with the rms noise for the AD7895 increasing. this effect will vary depending on where the serial clock edges appear with respect to the bit trials of the conversion process. it is possible to achieve the same level of performance when reading during conversion as when reading after conversion, depending on the relationship of the serial clock edges to the bit trial points.
AD7895 C11C rev. 0 dynamic performance (mode 1 only) with a combined conversion and acquisition time of 4.1 m s, the AD7895 is ideal for wide bandwidth signal processing applica- tions. these applications require information on the adcs effect on the spectral content of the input signal. signal to (noise + distortion), total harmonic distortion, peak har- monic or spurious noise, and intermodulation distortion are all specified. figure 11 shows a typical fft plot of a 10 khz, 0 v to +5 v input after being digitized by the AD7895 operating at a 198.656 khz sampling rate. the signal to (noise + distor- tion) ratio is 73.04 db, and the total harmonic distortion is C84.91 db. the formula for signal to (noise + distortion) ratio (see terminology section) is related to the resolution or number of bits in the converter. rewriting the formula, below, gives a measure of performance expressed in effective number of bits (n): n = ( snr 1.76)/6.02 where snr is signal to (noise + distortion) ratio. ? ?20 0 9.9k 10k 30k 50k 70k 90k ?0 ?0 ?0 ?0 ?00 ?0 ?0 ?0 ?0 ?0 ?10 f sample = 198656 f in = 10khz snr = ?3.04db thd = ?4.91db figure 11. ad7896 fft plot effective number of bits the effective number of bits for a device can be calculated from its measured signal to (noise + distortion) ratio. figure 12 shows a typical plot of effective number of bits versus frequency for the AD7895 from dc to f sampling /2. the sampling frequency is 198.656 khz. the plot shows that the AD7895 converts an input sine wave of 10 khz to an effective numbers of bits of 11.84, which equates to a signal to (noise + distortion) level of 73.04 db. 0 1000 200 400 600 800 10.0 11.4 11.2 11.0 10.8 11.8 11.6 12.0 10.6 10.4 frequency ?khz enob 10.2 figure 12. effective number of bits vs. frequency power considerations in the automatic power-down mode, then, the part may be operated at a sample rate that is considerably less than 100 khz. in this case, the power consumption will be reduced and will depend on the sample rate. figure 13 shows a graph of the power consumption versus sampling rates from 100 hz to 90 khz in the automatic power-down mode. the conditions are 5 v supply 25 c, serial clock frequency of 8.33 mhz, and the data was read after conversion. 0.1 90 10 20 30 40 0 5 4 3 2 7 6 8 1 frequency ?khz power ?mw 50 60 70 80 10 9 11 figure 13. power vs. sample rate in auto power-down mode
AD7895 C12C rev. 0 c2209C12C10/96 printed in u.s.a. outline dimensions dimensions shown in inches and (mm). plastic dip (n-8) 8 14 5 0.430 (10.92) 0.348 (8.84) 0.280 (7.11) 0.240 (6.10) pin 1 seating plane 0.022 (0.558) 0.014 (0.356) 0.060 (1.52) 0.015 (0.38) 0.210 (5.33) max 0.130 (3.30) min 0.070 (1.77) 0.045 (1.15) 0.100 (2.54) bsc 0.160 (4.06) 0.115 (2.93) 0.325 (8.25) 0.300 (7.62) 0.015 (0.381) 0.008 (0.204) 0.195 (4.95) 0.115 (2.93) soic (so-8) 85 4 1 0.1968 (5.00) 0.1890 (4.80) 0.1574 (4.00) 0.1497 (3.80) 0.2440 (6.20) 0.2284 (5.80) pin 1 seating plane 0.0098 (0.25) 0.0040 (0.10) 0.0192 (0.49) 0.0138 (0.35) 0.102 (2.59) 0.094 (2.39) 0.0500 (1.27) bsc 0.0098 (0.25) 0.0075 (0.19) 0.0500 (1.27) 0.0160 (0.41) 8 0 0.0196 (0.50) 0.0099 (0.25) x 45

▲Up To Search▲

Price & Availability of AD7895

	To Download AD7895 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .